Sorry for the delay...5" rain/3 hrs is big even by N.O. standards and I have been elevating things in my brewshack..
Revisiting an old friend-the Immersion chiller
The immersion chiller is often the novice brewer's first "technology based" piece of equipment.Simple and cheap to make and to operate,it can be fine tuned to a new level of efficiency.
Maintain maximum boil pot volume-instead of dropping it into the boil the last 10 minutes to sterilize which causes the already high boiling wort volume to rise,suspend it from an open weave frame (old oven shelf,old frig shelf,wire frame shelf, or custom made plastic/CPVC/metal frame).Tie 4 Cu wires at 4 equidistant balance points on the top and tie them to the bottom of a loop or ring which has another stout wire at the top as the anchor.Place the frame over the boiling wort with the ring below and the anchor fed through the center of the frame.Let out the anchor line until the IC sits a couple of inches above the surface which will be better than a dunk since steam is hotter and no space is taken up.At flame out,add any hops needed (BTW,this is a good time to sprinkle in sugar which will readily dissolve but not char since the flame which causes scorching is out;I frequently add sugar as do many British brewers.)
Lower the IC until it is just below the surface.
Minimize the pot heat-one of the reasons counterrflow chillers (or pumping wort out of the pot work so well is that the wort is taken away from the hot walls of the pot.The experiences of dropping dry ice into wort,watching it cool and then watching the temp rise again or simply putting one's hand on the side wall shows how much heat the pot holds.Remove any insulation,cover the jet of the burner with a can and hose the side walls for a couple of minutes.Observation #2 (Reference volume=Hank's Observations on Hot Things)--the bigger the temp difference between coolant and "coolee",the quicker the drop so now is best time to splash the pot with hose water of constant temp.
Rethink then remake the IC. A) Most ICs are smoothly curving coils that spiral down to sit on the bottom of the pot.From HOHT Observation #3-more turbulence,the less lamination and the more heat exchange.Convoluted Cu coils with elliptical twisted surfaces cool quicker than do straight runs so a kinky,various cross section shape coil is preferred.
B)HOHT Observation #4-heat rises.Why have the coil at the bottom except that the old design had it sitting on the bottom? Make a plani-spiral flat as wide as possible be so the entire top level cools and drops to bring up another level to be cooled.If anyone has access to some type of device it would nice to know how fast the levels move.
C)The first foot of the IC contains for example 70 degree water and when contacting 180 degree wort cools QUICKLY (see HOHT,again Observation #2)-and the next foot perhaps 75 and therefore little slower cooling and the next 79? but whatever the exact figures it is true that the first half of the coil offers faster cooling than does the second half.Why not have 2 "first halves"? When St Arnold of Metz (patron saint of brewing) caused my 40' coil to snap at about the 20' line as I was realigning it I recognized that he had sent me a message and I made a double barreled IC.Since then I learned that a neighbor/fellow brewer has a Trifecta.FWIW," Pivo Ron" also has a lot of info on all electric brewing (
http://hbd.org/rlaborde/rig.htm)
Whirlpool after removing IC
Dealing with the seasons-My Jefferson Parish water dept draws from the Mississippi and in mid August the river temp is 85 which is about what the hose delivers.BTW,I make lagers in the summer since I can offer a constant 45 in the frig easier than I can offer a constant 65 for ales.Prechilling the coolant in a Cu tube in ice bath does NOT really work since it requires the coolant to be kept to a trickle which defeats the rapid coolant flow needed;in zero flow-a terrible situation for chilling the wort -the 84 degree coolant and 32 degree ice bath meet eventually.84+32 =116;116/2=58 coolant whereas pumping the ice water delivers a 32+ degree coolant-much cooler.After a few runs U will know how much ice water water you circulate and can prepare enough but a more practical approach using ice is post chilling.
A post chiller in which wort trickles does work well but note it is the WORT not the COOLANT that trickles.If you are confident in your technique some clean dechlorinated ice cubes cool well with minor dilution but post chiller is much better approach.BTW,instead of cubes I use frozen bottles which I refreeze in the secondary frig's freezer
Love the planet
In a place that gets 70" rain/yr,water is plentiful but it is not cheap and on general principles I save expelled water to clean utensils and refill the pond.After a few runs U will know how much water you circulate and can prepare enough vessels.